Appboard/2.4/builder/widgets/actions/topology drill down - Revision history

imported>Cmace: action filtering based on data source, not data collection

2014-05-01T18:52:19Z

action filtering based on data source, not data collection

← Older revision		Revision as of 18:52, 1 May 2014
Line 25:		Line 25:
	### Click <b>Add Rule</b> to create one or more rules that indicate what data should trigger the Action, when selected.		### Click <b>Add Rule</b> to create one or more rules that indicate what data should trigger the Action, when selected.
	### Click <b>Close</b> to save the Filter settings.		### Click <b>Close</b> to save the Filter settings.
	## Select the Data ~~Collection~~ name. When the Widget is run, selection of data in this Data ~~Collection~~ will trigger the Action.		## Select the Data Source name. When the Widget is run, selection of data in this Data Source will trigger the Action.
	# Under <b>Topology Widget</b>, select the name of the Widget to drill down in when the Action is invoked.		# Under <b>Topology Widget</b>, select the name of the Widget to drill down in when the Action is invoked.

imported>Jason.nicholls at 09:03, 14 December 2013

2013-12-14T09:03:43Z

← Older revision		Revision as of 09:03, 14 December 2013
Line 1:		Line 1:
	{{DISPLAYTITLE:~~AppBoard Action -~~ Topology Drill Down}}		{{DISPLAYTITLE:Topology Drill Down}}
			[[Category:AppBoard 2.4]]
	The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another Widget. The other Widget in this case must be a Topology Widget with drill down capability.		The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another Widget. The other Widget in this case must be a Topology Widget with drill down capability.

imported>Mike.berman at 16:15, 5 September 2013

2013-09-05T16:15:04Z

@@ Line 1: / Line 1: @@
 {{DISPLAYTITLE:AppBoard Action - Topology Drill Down}}
 The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another Widget.  The other Widget in this case must be a Topology Widget with drill down capability.
@@ Line 12: / Line 15: @@
 Perform the following steps to configure the "Topology Drill Down" Action for a Widget:
-# Follow the instructions above to create the Action in the <b>Widget Actions</b> panel.
+# Create a Topology Widget with <b>Auto Node Drill Down</b> set to "Enabled".
 # <b>Name</b>: Enter a name for this Action.  For convenience, a default name is provided.  The Name is not used anywhere else in AppBoard, and only displayed on this configuration page.
 # <b>On selection of</b>:
@@ Line 24: / Line 29: @@
 == Sample Use Case ==

imported>Mike.berman at 00:47, 5 September 2013

2013-09-05T00:47:53Z

← Older revision		Revision as of 00:47, 5 September 2013
Line 5:		Line 5:
	== How To Create a Topology Drill Down Action ==		== How To Create a Topology Drill Down Action ==

	For instructions on adding a ~~Focus on Widget~~ Action, see the general instructions in [[appboard/2.4/builder/widgets/actions#How_To_Create_an_Action_in_a_Widget\|How To Create an Action in a Widget]].		For instructions on adding a Topology Drill Down Action, see the general instructions in [[appboard/2.4/builder/widgets/actions#How_To_Create_an_Action_in_a_Widget\|How To Create an Action in a Widget]].

imported>Mike.berman: Created page with '{{DISPLAYTITLE:AppBoard Action - Topology Drill Down}} The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another W…'

2013-09-05T00:47:24Z

Created page with '{{DISPLAYTITLE:AppBoard Action - Topology Drill Down}} The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another W…'

New page

{{DISPLAYTITLE:AppBoard Action - Topology Drill Down}}
The "Topology Drill Down" Action allows the User to click in one Widget and then invoke a drill down operation in another Widget. The other Widget in this case must be a Topology Widget with drill down capability.

== How To Create a Topology Drill Down Action ==

For instructions on adding a Focus on Widget Action, see the general instructions in [[appboard/2.4/builder/widgets/actions#How_To_Create_an_Action_in_a_Widget|How To Create an Action in a Widget]].

== How To Configure a Topology Drill Down Action ==

Perform the following steps to configure the "Topology Drill Down" Action for a Widget:

# Follow the instructions above to create the Action in the Widget Actions panel.
# Name: Enter a name for this Action. For convenience, a default name is provided. The Name is not used anywhere else in AppBoard, and only displayed on this configuration page.
# On selection of:
## Select "any" or "specific" for the type of data selection by the User that will trigger the Action. When selecting "specific", perform the following additional steps:
### Click the Filter button. The Filter Editor is displayed.
### Click Add Rule to create one or more rules that indicate what data should trigger the Action, when selected.
### Click Close to save the Filter settings.
## Select the Data Collection name. When the Widget is run, selection of data in this Data Collection will trigger the Action.
# Under Topology Widget, select the name of the Widget to drill down in when the Action is invoked.

== Sample Use Case ==